Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
What are your concepts about A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old tub is easily easily accessible, the task can relocate speedily; if you have to open a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the work and also fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This article will certainly assist you install a new bath tub in your restroom if you have currently gotten a new bathtub as well as don't need to transform the arrangement of your previous water supply pipelines.
Your tools as well as material list should comprise the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to avoid strain on the tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the bathtub in the called for position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub till the spirit level reads level.
To install taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and check all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as likewise check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the tub needs to wait until the bathtub has been made use of a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing complications with dampness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our section about How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our short article. Those who enjoyed our page if you please remember to share it. Thank you for your time invested reading it.
Best in town? Dial. Report this page